You are using an outdated version of Internet Explorer. Please upgrade your browser to improve your experience.
Profit Pointer for Selecting Advanced Tooling for High Quality Tube and Pipe
By Baicheng Wen, Ph.D. Roll-Kraft, Inc. Ohio U.S.A.
II. Tube and Pipe Tooling Designs
Several factors play a major role in tooling design. These include the material to be formed, the mill setup used in the forming process and the mill configuration. When designing tooling for a specific application, these elements must betaken into account. (Note: A detailed tooling analysis can be found in Reference 1.) Of particular importance to the tooling engineer is the type of material that is being formed. This has a significant impact on the design of the breakdown and fin section rolls where most of the strip is formed. The four most popular designs used in the breakdown section are (1) conventional, (2) standard edgeform, (3) versatile edgeform and (4) “W”, or reverse bending. Versatile edgeform and reverse bending breakdown sections are recommended when forming high strength materials. Typical strip flowers for these two designs are shown in Figures 1a and 1b, respectively. A large reduction in material springback and a better presentation of the strip edges into the fin pass are two major advantages to using versatile edgeform and reverse bending breakdown sections. Of these two designs, versatile edgeform is preferred for several reasons. First, this design forms more strip into the edgeform radius. Also, it reduces the possibility of kinking at the strip center that can be caused by reverse bending (see Figure 1b). Finally, strip marking is greatly reduced, resulting in an improved cosmetic appearance.
The primary function of the fin pass is to prepare the strip edges for welding. Four major designs are used. They are (1) round design, (2) flat oval design, (3) high oval design and (4) finless design. Of the four, the flat oval design is often recommended for high strength materials and high diameter-to-thickness ratio tubes. Several benefits are realized by using a flat oval fin pass. They include reduced material springback near the strip edges, elimination of the vertical peak at the bottom of strip that can be caused in the breakdown section and consistent, high quality welds. The major drawback to this design is the forming of a nonround tube when it enters the welder. As a result, more work is required in the sizing section. When a versatile edgeform breakdown section is utilized, a round design fin pass section can be used to avoid this problem. Since strip edges are adequately formed using this breakdown design, a round tube is produced in the fin section and less work is required in the sizing section. Accurate cross-sectional geometry is critical to reshaping round tubes into various tubular products. The first step in obtaining this geometry is calculating the circumferential shrinkage and the reduction in cross-sectional area required to produce the desired shape. This is done by evaluating the deformation and formability of the material. Next, the size of the round tube needed is established. Finally, the amount of work to be done in each pass is determined. It is important to remember that the strip is work hardened (material hardness and yield strength increase) as it passes through each stand. As a result, the tube becomes more difficult to form as it approaches its final shape. Therefore, it is suggested that most of the work be done in the first few passes in the reshaping section.
IV. Tooling Maintenance
V. The Continuation of Excellence
The final ingredient needed for producing high quality tube and pipe is a supplier with the expertise to manufacture the tooling you need. This is especially true for the advanced tooling needed to make tube and pipe for special applications. Such a supplier not only manufactures tooling, but can scientifically design it. Numerical methods that are based on advanced material deformation theory, such as finite element analysis, as well as computer aided design (CAD), are the foundation of their design process. Their design engineers are trained in metallurgy, material deformation mechanics, mechanical design and manufacturing processes. Additionally, they employ advanced manufacturing techniques and equipment, including CNC machinery, that ensures the production of quality, cost-effective tooling. Finally, they should offer a wide range of technical support that includes mill setup, tooling design, troubleshooting, tooling maintenance and rework services. A tooling supplier with these capabilities and range of services is a supplier you can trust to make the high quality, advanced tooling you need to manufacture pipe and tube to meet your customer’s needs.